Compact HPL Partitions in Imbaba, Cairo
Imbaba works at volume. The market areas trade from early morning, Kit Kat Square keeps traffic and people moving between the bridges and Ard El Lewa, Imbaba General Hospital serves a large population, and the former airport land has opened new development on the northern edge. Small washrooms here handle numbers that would strain a mall. Cairo House EG supplies and installs compact HPL partitions across the district.
What compact HPL partitions are, and why Imbaba buildings need them
Compact HPL is high pressure laminate manufactured as a solid slab rather than a decorative face over a soft core. Kraft paper is saturated in phenolic resin and pressed under heat into one dense homogeneous board, normally 12mm or 13mm for cubicle work. The panel is waterproof through its full thickness and carries its own load.
What makes Imbaba difficult is the ratio of use to floor area. A washroom serving a market unit or a clinic here might see several hundred people a day through two cubicles, with cleaning happening between rushes rather than after closing. Systems designed around gentle domestic use do not survive that, and the failure shows up first at the door edge and the hinge fixings.
Because the wearing parts are the fittings rather than the panel, the practical question is how quickly a broken latch gets fixed. We supply stainless steel 304 hardware and hand over spares at completion, so a failure is a ten minute repair by your own staff rather than a cubicle locked out of service for weeks.
Panel and hardware specification
| Specification | What we supply for Imbaba washrooms |
|---|---|
| Panel thickness | 12mm standard cubicles, 13mm for high traffic and public washrooms |
| Core | Solid phenolic kraft core, waterproof through the full thickness |
| Hardware | Stainless steel 304 hinges, indicator locks, brackets, pilaster shoes, coat hooks |
| Door action | Gravity or spring hinges, self closing, adjustable to open or closed rest |
| Head rail | Anodised aluminium, continuous over the cubicle run |
| Floor fixing | Adjustable stainless feet, levels out uneven screed |
| Typical lead time in Imbaba | Four to seven working days after approval |
| Finishes we move most here | Dark hard wearing solids that stay presentable under heavy use |
Where compact HPL earns its cost in Imbaba
Markets and trade
The market areas trade from early morning with washrooms shared between traders, staff and the public in effectively continuous use.
Hospitals and clinics
Imbaba General Hospital and the surrounding practices need non porous seamless surfaces that hold up to frequent disinfection.
Retail
Ground floor shops across the district run washrooms with a use to floor area ratio far beyond what the room was designed for.
Food outlets
Restaurants and takeaways concentrate their turnover into the evening in washrooms with no spare width for a badly cut door.
Workshops and light industry
Service and workshop units run staff washrooms in dusty conditions where a wipe clean non porous panel is the only sensible option.
Schools
Schools across Imbaba and Ard El Lewa move large groups through washrooms in short breaks, loading door edges and hinges hardest.
What we supply and install in Imbaba
Cairo House EG has supplied construction finishing materials in Cairo since 2015 and holds the exclusive Egypt agency for UNISCE compact HPL panels. Everything below is fabricated and fitted by our own teams rather than subcontracted out.
Toilet cubicles and urinal screens
Full cubicle runs in 12mm or 13mm compact HPL, with matching urinal divider screens and anodised aluminium head rails. See HPL toilet cubicle panels.
Solid surface vanities
Solid surface vanity units built as one continuous piece, which is the detail that makes a washroom easy to clean. See seamless vanity units.
Solid surface tables
Table tops in matching colours across a whole venue, fabricated as one batch. See solid surface tables.
Washroom counter tops
Counter surfaces in the same colour family as the cubicles, so the washroom reads as one specification. See compact HPL counters.
Partition hinges
Gravity and spring hinges in stainless 304, adjustable to rest open or closed depending on how the washroom is used. See self closing partition hinges.
Adjustable pilaster feet
Pilaster shoes that cover the fixing and keep water away from the base of the panel. See adjustable pilaster feet.
Serving Imbaba and the northern west bank
We work from El Nozha El Gedida in Heliopolis and cross to Imbaba over the bridges. Bridge traffic rather than distance sets the timing, so we plan surveys and deliveries around it and quote installation windows we can genuinely hold.
On the same side we cover Agouza, Zamalek, Mohandessin, Giza and Shoubra El Kheima across the river. A landlord or contractor with several units across the north west usually gives us the whole set.
Access here needs planning. Streets around the markets are narrow and congested for most of the day, many buildings have no lift, and loading has to be timed carefully. We record all of it at survey and cut panels to suit the route. You can also see tailored project solutions.
What to expect when you work with us
Most washroom packages fail at measurement, not installation. Our process removes that risk before a single panel is cut.
- Site survey. We measure the built washroom in Imbaba rather than working from the drawing, because wall plumb, floor level and drainage falls on site rarely match what was issued.
- Layout and panel selection. You receive a cubicle layout with door swings and clear widths marked, plus physical panel samples so the colour is approved under your own lighting instead of on a screen.
- Quotation. Itemised by panel, hardware and installation, so you can see what is being priced and adjust the specification if the budget needs it.
- Fabrication. Panels are cut, edge finished and drilled to the approved layout. Sheets stay under factory film until they reach site.
- Installation. Our fitters strip the old system where needed, set out, install head rails, pilasters and doors, then adjust every hinge and latch before handover. Small washrooms are usually completed in a single day.
- Handover and after sales. We walk the finished washroom with you, hand over spare hardware, and stay reachable for adjustments once the space is in real use.
Find Us on Google Maps
Frequently Asked Questions
Our two cubicles serve hundreds of people a day. What actually lasts? A solid panel with stainless steel 304 hardware. The panel takes impact without a face separating from a core, and the fittings are the wearing parts, replaceable individually in minutes with spares you hold on site.
Cleaning happens between rushes rather than after closing. Is that a problem? No. The surface is non porous with no coating to strip, so frequent quick cleaning works perfectly well and does not gradually degrade the finish the way it would on a coated panel.
Can you replace a failed system without rebuilding the washroom? Yes. Where the floor and walls are sound we strip the old cubicles and fit compact HPL to the existing layout, normally in a single day on site for a small washroom.
Delivery access around the market is very difficult. How do you manage? We cut panels to size in the workshop and plan the vehicle and timing at survey around the street and the hours it is passable, rather than arriving with full sheets at the busiest point of the day.
What thickness should a high traffic small washroom use? 13mm where the flow is genuinely public all day, such as a market unit or a clinic. 12mm is sufficient for staff only washrooms and costs less.
Can our own staff replace a broken latch? Yes. Hinges, latches and brackets are standard stainless steel 304 parts that unbolt and swap without touching the panel, and we hand over spares at completion for exactly this reason.
Can you work outside trading hours? Yes. Most Imbaba work is done outside trading hours, agreed at survey so delivery, cutting and installation are planned around your business.
What does a compact HPL partition cost in Imbaba? It depends on cubicle count, thickness, colour and hardware. Send rough dimensions or a photo of the washroom and we return an itemised quotation.
Get a quote for your Imbaba project
Send the cubicle count and rough dimensions, or a photo of the washroom, and we will return an itemised quotation including strip out where it is needed.
Site visits across Imbaba and Ard El Lewa are arranged within the same week. To send us your drawings, call or message us any time.
Phone: +201066672094 or +201223111265
Website: cairohouseeg.com
Hours: Open 24 hours, 7 days a week
Address: 3 Misr Lel Tayaran Street, Block 1314, Civil Aviation Buildings, next to Sindbad, El Nozha El Gedida, Cairo 11843